Some time ago I had to install a machine gun on one of our division ...
So, the kit consists of a forearm B-50 , the stock PT-2 , muzzle brake - compensator DTK-1P and front handle RC-1 with bracket B-25U ...
The fore-end is formed when communicating between a three-piece ...
Top, if desired, set the bar low for installing red dot scope.
Included are two sets of plastic spacers and screws of different lengths, mounting plates ...
Included are two sets of plastic spacers and screws of different lengths, mounting plates ...
Long set screws and spacers for installation on the forearm gun control panel ...
Next the position of our hit parade - butt PT-2 ...
The design uses a height-adjustable butt plate PT-1 Stripped suspension strap. Instead, on the fore-end dress "Shoe" from the set of the GP-25 ...
The buttstock is adjustable in length.
Basic elements - the screw and two guides ...
The mount of the butt to the shank receiver gun ...
The mount to the shank and bottom butt plate detached from the middle part of the butt ...
Butt cheek of PT-1 and staff are the AK pistol grip for easy anchoring.
The handle is a replacement lug regular stock ...
The handle is a replacement lug regular stock ...
Muzzle brake - compensator DTK-1P ...
Front handle RC-1 to B-25U adapter is designed for comfortable holding a machine gun mounted on the forearm and the B-50 ...
We proceed to the assembly.
Disconnect the regular stock. The most difficult stage, because the screws expanded on the butt, and prevents beading insert a screwdriver into the slot nuts, and without the screw with the nut rotated ... etc. etc.
However, unscrewed the screws and set aside. Gun ready to the assembly ...
Disconnect the regular stock. The most difficult stage, because the screws expanded on the butt, and prevents beading insert a screwdriver into the slot nuts, and without the screw with the nut rotated ... etc. etc.
However, unscrewed the screws and set aside. Gun ready to the assembly ...
Standard screws attach the butt ...
If desired, the stock can be shortened.
This option is available at remaking the machine gun in the layout Bullpap, or if you want to remove the stock to reduce the size of ...
This option is available at remaking the machine gun in the layout Bullpap, or if you want to remove the stock to reduce the size of ...
Tying wall forearm so that notches in the side sections fore dressed to the spigot.
And tighten the six screws.
Pins - these are things tidy ...
And tighten the six screws.
Pins - these are things tidy ...
Attach the bracket to the plate ...
In this case, the replacement barrel is impossible.
As a way out this situation, if the problem is urgent, you can set the bar B-12 ...
As a way out this situation, if the problem is urgent, you can set the bar B-12 ...
True, this ersatz - bit version of the rail on the right, as it is designed to fit in complete with a machine-gun of.
But the barrel is replaced with no problems.
And in order to make a stable connection, you can make the right wall in the forearm and arm one piece of T - shaped blanks.
But the barrel is replaced with no problems.
And in order to make a stable connection, you can make the right wall in the forearm and arm one piece of T - shaped blanks.
Install the flame arrestor DTC.
To do this, remove the flash suppressor, the removal of which became a big problem ...
To do this, remove the flash suppressor, the removal of which became a big problem ...
Tie, by the way, was not easy. This is because the trunks are usually served without removing the flash suppressor. With clear consequences ...
Compensator has two notches to lock ...
... Allowing it to set at an angle to counter diversion barrel when firing ...
Left stick handle ...
Italic version of the owner did not like guns. And as his hands were large and long, as he was, he had the usual and RC-1, shifted forward ...
The fact that the gun is not left out in terms of attention tuning - this is very good.
To be able to replace the barrel during a collimator forearm can be "slightly" upgraded.
To be able to replace the barrel during a collimator forearm can be "slightly" upgraded.
Our gunners, especially tall or especially - tall, most complaints brought the butt. Of course, it was designed without the involvement of users.
But, as it turned out not all :)
Representative of the company in a conversation with me noticed that the stock was created for the "ordinary" people.
And our gunner, whom he knew personally, he asked him to convey to he looked at himself in the mirror and estimated its size :)
Representative of the company in a conversation with me noticed that the stock was created for the "ordinary" people.
When extending the stock to the maximum he thoroughly backlash. No such good detail and pleasant to use as shoulder strap.
So my comments. Adjust the length of the stock could be used and the type of PT-1.
So my comments. Adjust the length of the stock could be used and the type of PT-1.
And instead of misleading when viewing satellite images CIA analysts, the second pistol grip, set the lines which gunner put any front handle with the container.
Or folding. Or monososhku. Or do not put.
Or folding. Or monososhku. Or do not put.
So God himself commanded to develop a folding butt. The more that overseas counterparts already have. Well Pecheneg -2 with the butt of a place to be ...
Keine Kommentare:
Kommentar veröffentlichen